口模,die英语短句,例句大全

口模,die
1)die[英][dai][美][da?]口模
1.Design of Plastic Profile Extrusion Dies;塑料异型材挤出口模设计
2.Preliminary study of extrusion die design by rheology挤出口模设计中的流变学初步研究
3.By means of the visualization device,the flow trajectories of polymer melts in an cuneiform convergent extrusion die were recorded by video.利用可视化实验手段,动态拍摄了楔形收敛挤出口模内聚合物熔体的流动轨迹线,借助于轨迹线,分析了熔体在口模中的流动状态,同时通过实验得到了熔体在口模过渡区内的停留时间与挤出流量之间的关系。

英文短句/例句

1.FS Switch to full screen mode. /WM Switch to window mode.FS切换到全屏模式./WM切换到窗口模式.
2.Deep Web Form Schema Extraction and Schema IntegrationDeep Web入口模式抽取与模式集成
3.The Design of Router s Interface Module--The Design of Ethernet Module and Ethernet Module;路由器接口模块设计——Ethernet模块和ISDN模块的设计
4.Population and Development Simulation Model人口与发展模拟模式
5.This interface should be placed in the interfaces module of the messageboard.该接口将代替留言薄的模块接口。
6.module interface cross-reference模块接口相互对照引用
7.password protected load module file口令保护装入模块程序
8.type genus of the family Catostomidae.亚口鱼科的一个模式属。
9.simulate voice synthesizer模拟口声语音合成器
10.container terminal capacity model集装箱港口容量模型
11.monolithic D/A interface单片式数字模拟接口
12.storage module drive interface存储模块驱动器接口
13.input/output interface control module输入输出接口控制模块
14.Population-Household Consumption Projection人口－住户消费预测模式
15.A: We brought fruit juice.口试模拟实战演练（一）
16.Integrated Macro Model for Population and Development人口与发展综合宏观模式(人口发展宏观模式)
17.Simulation Model on Population and Development (Game of Training)《人口与发展模拟模式》（训练游戏）
18.A/D,D/A Interface of Single Board Microcomputer andIts Application单板微型机的模/数、数/模接口及其应用

相关短句/例句

expanding and necking die扩口、缩口模
1.According the structure characteristics of oil filling pipe,combining production experience,designed expanding and necking die.针对加油管的结构特点,结合企业生产经验,给出了连续扩口、缩口模设计方案。
3)gate[英][ɡe?t][美][get]浇口，进模口
4)inlet[英]['?nlet][美]['?n'l?t]进模口，闸口
5)riser gate冒口进模口
6)Die design口模设计
1.After an analysis on the velocity distribution obtained from numerical simulation, the original die design was modified;and the length of each part of molding zone was determined according to the principle of flow rate equilibrium.研究还表明:对于异型材挤出口模设计,不能把口模截面视作若干规则形状截面的简单几何组合,必须把其当成一个整体来对待;过渡区不仅影响成型区的流动,而且对稳流区的流动也有不可忽视的影响,设计时应对过渡区给予足够的重视。
2.The gas-assisted extrusion,fiber spinning,hollow fiber and microporous membrane technology were contacted for the first time,and the actuality of these technologies and the characteristics of die design were introduced breifly at home and abroad.首次将气辅挤出、纤维纺丝、中空纤维及微孔薄膜技术联系起来,并简要介绍了国内外这些技术的研究现状和口模设计的特点。