1)crankshaft[英]['kr??k?ɑ:ft][美]['kr??k'??ft]曲拐轴
1.Computing method on strength analysis of combination typed tri-crankshaft;组合式三曲拐轴的强度分析计算方法
2.Mechanics analysis based on crankle instead of crankshaft;活塞压缩机曲柄轴改曲拐轴的力学分析
英文短句/例句
1.Thus a normal loom has two shafts. The main shaft(crankshaft or top shaft) drives the lay mechanism and is geared to another shaft which operates at half of the speed of the crankshaft.这样,普通织机应具备两根轴,主轴(曲拐轴或位于上部的轴)驱动筘座并通过齿轮驱动另一根轴。
2.Analysis of Inspection and Measuring Method for 120° Distributing Angle Errors of Crankshaft Crankpins曲轴曲拐120°角度误差检测方法分析
3.Research on the Upset Forging Technology of Marine Crank of 305 Crankshaft船用305曲轴曲拐镦锻成形工艺研究
4.Research on a Newly Combinational Tri-turned Crankshaft for Diaphragm Pump新型组合式隔膜泵用三拐曲轴的研究
5.Analysis on Measuring Accuracy in Inspecting Crank Angles for Six-cylinder Crankshafts六缸发动机曲轴曲拐夹角检测方法的精度分析
6.Study on Making Process and Mould Structure of None-phase Angle Crankshaft with Four Cylinder Sleeve无相位角四拐曲轴的制坯工艺及模具结构优化
7.crankshaft (main journal turning lathe)曲轴（主轴颈）车床
8.triple-barrel pump三联式筒泵(三个泵筒与一个吸液管相连，由三拐曲轴驱动三个活塞产生均匀液流)
9.upper center crankshaft bearing曲轴主轴承上中轴瓦
10.Inflection Point拐点，弯曲点，转折点
11.Full of twists and turns;tortuous.弯弯曲曲的；迂回的充满弯曲和拐弯的；曲折的
12.crankshaft journal face hardening machine曲轴轴颈表面淬火机床
13.Crankshaft main journal out of round or worn曲轴主轴颈不圆或磨损
14.crankshaft journal milling machine曲轴轴颈铣削专用机床
15.Replace crankshaft or grind journals更换曲轴或磨光轴颈
16.The feed holes for the crankshaft main bearings.曲轴主轴承进入口。
17.Crankshaft and main bearings service曲轴和主轴承的维修
18.crankcase cam gear bushing曲轴箱凸轮传动轴衬套
相关短句/例句
Four crank四曲拐轴
3)split-pin crankshaft错拐曲轴
1.Influence of Constraint Condition on FEA for Split-Pin Crankshaft;约束条件对错拐曲轴有限元分析的影响
2.The general methods for the balancing analysis of inertia forces in the internal combustion engine(ICE) that adopted split-pin crankshaft technology was studied in this paper.针对某V6柴油机,对比分析了该柴油机采用错拐技术前后倾覆力矩及惯性力系的变化情况,结果表明,错拐曲轴平衡技术可有效抑制内燃机内部的激励载荷,是改善内燃机振动、噪声特性极为有效的技术措施之一。
4)Stagger crankshaft错拐曲轴
1.Using ANSYS software, the finite element analysis for the stagger crankshaft of a 60°V6 vehicle gasoline engine was conducted under extreme operation conditions.应用ANSYS软件,对某60°夹角V6车用汽油机的错拐曲轴进行了不同极限工况下的有限元计算,尤其对该曲轴的载荷和约束条件做了较为详细的讨论,得到了该错拐曲轴的应力分布,并校核了其静安全强度。
2.The structural strength difference between stagger crankshaft and common crankshaft and the influence of Various loads and different sliding bearing clearances on stagger crankshaft strength are studied.以90°夹角的某V型6缸柴油机为例,应用有限元分析方法,研究探讨了采用错拐结构前后曲轴强度的变化,以及不同载荷、不同主轴承间隙等因素对错拐曲轴强度的影响,并通过实验验证了有限元分析的正确性。
3.The analytical method based on FEA and experiments is used to study the structural strength of diesel engine stagger crankshaft.通过对比表明:理论分析与实验实测结果具有较好的一致性,针对错拐曲轴所采用的计算分析方法与实验方法均是合理可行的。
5)crankshafts/single crank throw曲轴/单拐
6)five staggers crankshaft五拐曲轴
1.Free-forging process research on five staggers crankshaft of natural gas compressor;天然气压缩机五拐曲轴自由锻工艺研究
延伸阅读
脖子拐1.见"脖拐"。
