1)Pin[英][p?n][美][p?n]销轴
1.Fracture Analysis of Pin in Metalforming Machinery;双点闭式锻压机销轴断裂原因分析
2.An Analysis of the Mechanism of the Conveying Chain Pin Breakage in a Bucket Elevator;斗式提升机输送链销轴断裂机理分析
3.Then it discusses upon principally the friction state, wear form, wear principle and the transfer way of the sleeving and pin hinge in the chain, and supplies necessary countermeasures to improve the abrasion resistance and service life of the chain.在此基础上,重点对链条中套筒和销轴铰链副的摩擦状况、磨损形式、磨损机制及转换进行了论述,并就提高链条耐磨损能力和使用寿命提出了必要的应对措施。
英文短句/例句
1.The Analysis of Fracture Axis Pin Made of 18Cr2Ni4WA Steel;18Cr2Ni4WA钢销轴断裂失效分析
2.The piston end of the rod is attached to the piston by the piston pin, or wrist pin.连杆的活塞端用活塞销或销轴安装在活塞上。
3.The Rupture Failure Reason and Analysis of the Pivot;42号自卸车销轴断裂失效分析及研究
4.In order to represent this behaviour, we can consider one of the supports to be a pin support and all the others to be roller supports.为阐明这一特点，设梁的支承之一为销轴支承，其他均为辊轴支承。
5.Installation Technologies of Preburied Prestressed Anchor Bolts of Wide Diameter Pin Roll Hinge Supports预埋预应力锚栓的大直径销轴铰支座安装技术
6.The Improvement of Connecting Pin-lubrication in Tension Roller Compactor Frame张力压紧辊架连接销轴润滑方式的改进
7.Structure Design of Long-Stroke Chain-Type Pumping Unit with Axis Reversing销轴换向链条式长冲程抽油机结构设计
8.The pin holds the wheel on轴销把轮子固定起来。
9.Elastic pin couplingGB/T5014-1985弹性柱销联轴器
10.The rod-bearing cap attaches the connecting rod to the crankpin.连杆轴瓦盖将连杆安装到曲轴销上。
11.As the crankshaft rotates, the crankpin swings in a circle around the shaft.随着曲轴的转动，曲柄销绕主轴作圆周摆动。
12.A pin or a bolt on which another part pivots.枢轴，柱销，扣针在另一铆钉上的扣针或销子
13.A metal pin that joins two pieces of stone.轴头销把两块石头钉牢在一起的铁销钉
14.The horizontal axis shows sales in millions of dollars.横轴表示以百万为单位的销售额。
15.Gear coupling with elastic pinGB/T5015-1985弹性柱销齿式联轴器
16.Pin coupling with elastic sleeveGB/T4323-1984弹性套柱销联轴器
17.There is a pin hole between outside shell and output axis.外套与输出轴的径向有一个插销孔。
18.The Target Marketing of Voith for Cardan Shaft in Chinese Market;福伊特万向轴在中国市场的目标营销
相关短句/例句
pin shaft销轴
1.The experience ofusing the pin shafts ofpulling cable and balance cable in Huangshan Yungu cable w ay;黄山云谷索道牵引索、平衡索锚固销轴的使用经验
2.The mechnical property of SACM 645 pin shaft aften heat treatment is proved can meet the technical requirments by 910±10 ℃ oil quenching and 630±10° water quenching.对直径110mm的SACM645销轴进行了不同的热处理工艺试验,试验结果表明经910±10℃油淬(保温1。
3.The article analyses the existing calculation method of pin shaft joint partial strength, study the finite element modeling problem of pin shaft joint in girder structure and specific calculation procedure.分析销轴联接局部强度现有计算方法,探讨梁杆结构中销轴接头的有限元建模问题及具体的计算过程。
3)pin axle销轴
1.Problems existed in the pin axle of type EBJ—160 roadheader and method for solving;EBJ-160型掘进机销轴存在的问题及解决办法
4)shaft[英][?ɑ:ft][美][??ft]轴销
1.This paper introduces the method and steps of the local stress strain method to analyze the fatigue with the application of ANSYS,uses this method to analyze and calculate the fatigue-life of the press-sensor shaft both before the optimization and after the optimization to give the basis of the judgement of how the optimization influences the fatigue damage of the shaft.详细介绍了疲劳分析中的局部应力应变法分析方法和步骤,同时结合ANSYS,运用局部应力应变法中的稳态法对优化设计前后的压力传感器轴销分别分析、计算出了疲劳寿命,为优化设计对其抗疲劳性能的影响提供了客观的判断依据;对一般零部件的疲劳寿命的计算也有一定的参考价值。
2.By using ANSYS software,this paper calculates and analyses the stress of the shaft of the press-sensor and optimizes some important dimensions and gives the optimized results.采用有限元分析软件ANSYS,对某型号压力传感器的轴销进行了应力计算和分析,同时对其重要尺寸进行了优化设计和计算,得出了相关尺寸的优化序列以及优化曲线,大大提高了设计效率和设计质量。
5)shaft pin轴销
1.This article introduces structure, characteristic, stress analysis and theoretical calculation of shaft pin cutting type load cell.本文介绍了轴销剪切式称重传感器的结构与特点,受力分析与理论计算。
6)centre pin销轴，枢轴，主销
延伸阅读
活销销1.方言。指开关。
