压杆,compression bar英语短句,例句大全

压杆,compression bar
1)compression bar压杆
1.Calculated length of compression bar in pile bent column pier;单排桩柱墩压杆的计算长度
2.Stability and reliability optimization of arbitrarily-distributed parameters for compression bars;任意分布参数的压杆稳定可靠性优化设计
3.A new approximate formula for the large deflection problem of compression bar with two ends are simply supported is obtained,by the use of Ritz-Galerkin method.通过非线性振动中常用的里兹-伽辽金法,推出了两端铰支压杆大挠度问题的一个新近似公式,计算结果表明具有较高的精度。

英文短句/例句

1.Experimental Study of Compressive Buckling for an Axial Compressible Rod轴向可压缩压杆的压缩失稳实验研究
2.Strut-and-tie Model of Deep Beam Design Under Uniform Distributed Loads均布荷载下深梁设计的压杆-拉杆模型
3.Discussion on Hopkinson Bar Test Method;Hopkinson压杆测试技术探讨
4.Design of a piezoelectric bar sensor based on MATLAB;基于MATLAB的压杆测压传感器设计
5.Design of Reinforced Concrete Deep Beam Based on Strut-and-tie Model;钢筋混凝土深梁基于压杆—拉杆模型的设计
6.The Interactive Buckling of T-Section Columns with Axial Compress;T形截面轴心受压压杆的局部失稳与整体失稳
7.Research on Hydraulic Loading System for the UHV Tower Test Base特高压杆塔试验基地液压加荷系统研究
8.bar actuated pressure vent杆式驱动液压排出孔
9.helical spline type actuator带螺旋活塞杆的液压缸
10.reel height hydraulic adjuster lever拨禾轮高度液压调节杆
11.Install the hydraulic valve tappets.安装液压气门挺杆。
12.reaming and pushing machine for piston connecting rod bush活塞连杆衬套铰压机
13.low noise air screw compressor低噪声螺杆空气压缩机
14.double-column screw type supercharge device双柱丝杆式加压装置
15.remote operation cylinder lever分置式液压油缸操纵杆
16.hour counter operating lever hook时计数器活动杆构压片
17.Structure Optimization for Hydrostatic Supporting Bush of Crank Shaft and Rod Type Hydraulic Motor曲轴连杆式液压马达静压支承连杆瓦结构优化
18.A Hydraulic-Mechanical Driving Press with Bi-bar Toggle-lever Force Amplifier in Series铰杆-杠杆串联增力液压-机械复合传动压力机

相关短句/例句

column[英]['k?l?m][美]['kɑl?m]压杆
1.Critical press analysis on cracked slender columns;含裂纹细长压杆临界力分析
2.Process condition of upsetting shoulder was discussed and forming force was calculated based on column buckling theory.基于压杆稳定理论,探讨了该制件镦压凸肩的工艺条件,计算所需的工艺力,介绍其镦压成形模具的设计结构、工作原理。
3.In this paper the stability of a compressed column with initial imperfection and arbitrary supported ends is studied systematically.对各种边界条件下初始缺陷压杆的稳定性进行了系统的研究,讨论了不同边界条件和初始挠度对压杆稳定性的影响,得出了求解弹性边界约束系数、端点转角、端点弯矩和压杆挠度的公式,为进一步的理论分析打下了基础。
3)Compressive bar压杆
1.Reliability-robust design of compressive bar under incomplete probability information;不完全概率信息的压杆稳定可靠性鲁棒设计
2.Reliability-based robust design of compressive bar;压杆稳定可靠性稳健设计
3.Stable reliability-based sensitivity design of compressive bar;压杆稳定可靠性灵敏度设计
4)strut[英][str?t][美][str?t]压杆
1.Experimental study on flexural torsional buckling of cut-T struts;剖分T型钢压杆的弯扭屈曲试验研究
2.The method is proved to be both accurate and simple by comparing the theoretical values with the experimentally measured values of the elastic stability tests of struts and frames.分析了结构失稳时Ｐ－δ试验曲线的图形性质；提出了以最大曲率推算结构失稳临界荷载；并导出了相应的计算公式，压杆和刚架弹性稳定试验的实测数据说明本文所述方法既精确又简便，特别是结构或模型不允许作破坏试验时，可直接推算失稳临界荷载。
3.The width-thickness limit of T-section strut prescribed in the code for design of steel structure (GB50017—2003) is broadened so as to promote the using of the hot-rolled cut T-section strut.《钢结构设计规范》(GB5 0 0 1 7— 2 0 0 3 )放宽了热轧剖分T型钢压杆腹板高厚比限值 ,促进了剖分T型钢的推广使用。
5)compressive rod压杆
1.Using the fundamental knowledge of mathmatical analysis,this paper estabilishes the general controlling equation of a compressive rod under a combined load.利用数学分析的基本知识建立了联合载荷作用下压杆的一般控制方程。
2.By analysizing the natural properties of a compressive beam and removing the ordinary solution,this paper gives a detail method for calculating the critical forces of compressive rods with several kinds of different boundary conditions using vibration theory.以轴向受压梁的固有振动分析为基础,利用线性代数的基本知识,通过去除平凡解的方法,导出了计算压杆临界力的公式。
6)compression member压杆
1.This article presents a unified analysis of the limiting slenderness of plate elements of compression members with three commonly used sections.本文统一分析了轴心压杆三种常用截面的板件宽厚比限值。
2.There is no specification for the design of welded H section or box section compression member which plate thinkness is over 40 mm.对于板厚达４０ｍｍ以上的厚板焊接Ｈ形或箱形压杆承载力的设计，我国目前尚无规范可循。