衬套,bush英语短句,例句大全

衬套,bush
1)bush[英][b??][美][bu?]衬套
1.Influence of the seal ring s compressibility within gear pump on the bush s static balance;齿轮泵密封圈压缩量对衬套静力平衡的影响
2.FEA for a double-helix single screw pump bush profile;双头单螺杆泵衬套型线分析
3.The deformation, stress and strain's distribution of the double-helix single screw pump bush are discussed when the bush is under equal pressure, disordered pressure and the static contact with the bush and screw.用ANSYS对双头单螺杆泵衬套的受力情况作了有限元计算,为了提高计算效率,将螺杆泵衬套的有限元模型简化为平面应变模型求解。

英文短句/例句

1.fitting rubber liner for stern tube尾轴管橡胶衬套嵌套
2.drive bushing, Kelly,for well-drilling machines凯氏传动衬套,钻井机用
3.chromium-plated thin-walled steel cylinder liner钢质薄壁镀铬汽缸衬套
4.shock absorber eye bolt sleeve减震器有眼螺栓衬套
5.crankcase cam gear bushing曲轴箱凸轮传动轴衬套
6.governor upper bush调速器上部轴承衬套
7.governor bottom bush调速器下部轴承衬套
8.Liners can be located at several stations.衬套可以分别放在几处。
9.reaming and pushing machine for piston connecting rod bush活塞连杆衬套铰压机
10.front spring eye bushing前钢板弹簧卷耳孔衬套
11.Here is your slippersadaptors,sir.先生，这是您的拖鞋衬套。
12.universal-joint bushing and ring spider万向节衬套及球十字架
13.hoist pump drive shaft bushing起重机油泵传动轴衬套
14.spring hanger bushing replacer弹簧挂钩衬套换装器
15.Distributor Driveshaft Bushing Installation分电器驱动轴衬套安装
16.Morse taper bush without tang无扁尾莫氏圆锥衬套
17.morse taper bush with tang带扁尾莫氏圆锥衬套
18.Special liners are also available for inserting into unlined channels.专用的衬套也可用来嵌入无镶衬的渠道里。

相关短句/例句

Bushing[英]['bu?i?][美]['b????]衬套
1.Discussion About Wall Thickness Tolerance and Wall Thickness Difference of Bushing;小议衬套壁厚公差与壁厚差
2.Interference Fit of Bushing and Hole by Using Cold Extrusion;用冷挤压法实现衬套与孔的干涉配合
3.Fractures occurr frequently in the bushing made from high speed tool steel on the bearing system of blast hole rock bits A big increase in toughness is obtained through low temperature quenching and parameter optimization The industrial test shows that the fracture rate declines from 90%~96% by 7%~13% and drilling meters increase by 17%.用高速钢制作矿用牙轮钻头轴承系统的衬套 ,普遍存在破裂现象 ,通过采用低温淬火和优化工艺参数 ,其韧性大幅度提高 ,工业试验的破裂率由传统的 90 %～ 96 %下降到 7%～ 13 % ,钻头穿孔米道提高了 17%。
3)liner[英]['la?n?(r)][美]['la?n?]衬套
1.Analysis and application of liner burning and rotary liner mechanism of connected bar;连杆衬套烧研、转套机理分析与应用
4)lining[英]['la?n??][美]['la?n??]衬套
1.New methods for fast removing troubles from lining;快速排除衬套故障的新方法
2.Thin-wall linings are easy to deform in processing and assemblying,this paper puts forward solutions to solve this problem.本文针对薄壁衬套类零件易产生加工装配变形的问题 ,根据实际经验提出了解决措施 ,经实践使用证明 ,效果理想。
5)sleeve[英][sli:v][美][sliv]衬套
1.In this article a new calculation technique for stresses in the bush sleeve (shell), strengthened by a case, pulled on it, in the electromotor of the pressurized pump is offered.本文提出一种压力泵中电磁马达含外壳的衬套应力计算新方法。
2.Based on worksite practice,the paper introduces Cleaning and Overhaul Technology of the chock, bushing,sleeve which are the key parts in the oil film bearing.本文以现场实际经验为基础,重点介绍了轴承座、锥套和衬套这三个油膜轴承中关键件的清洗和检修技术。
6)bush[英][b??][美][bu?]衬套轴衬