1)puller[英]['pul?][美]['p?l?]拉拔器
1.We use homemade bolt puller to preload the clamp bolt,which more accurately controls the preload of the clamp bolt,and ensures the clamp\'s holding effect on the main cable.采用自制螺栓拉拔器对索夹螺栓进行预紧,更加精确地控制了索夹螺栓的预紧力,确保索夹对主缆的握紧效果。
2.To fully utilize the advantage of hydraulic technology,the paper designs a kind of miniature type two-way hydraulic puller to be used in maintenance of agricultural machinery,which overcomes disadvantages of traditional puller,for example,low efficiency,cumbersome and unsuitable to portable etc.充分利用液压技术的特点,克服了传统拉拔器拆装效率低、笨重和不易携带等缺点,设计了一种应用于农机维修中的小型双向液压拉拔器。
英文短句/例句
1.Distributor Bushing Puller C-3052分电器套管拉拔器C-3052
2.Puller Set—C-293-PA拉拔器套件—C-293-PA
3.Cylinder Liner Puller VM, 1001汽缸套拉拔器VM, 1001
4.Hold puller screw and tighten puller nut until bushing is remove握紧拉拔器螺栓，拧紧拉拔器螺母，直至拆下衬套。
5.Remove the special gear puller and adapter tools from timing gear cover.从正时齿轮罩上拆卸专用齿轮拉拔器及接头工具。
6.This is the land of the elec-tric salad dryer, the electric can opener, the electric soap dispenser, the electric air freshener, the electric hair curler, the in-the-shell egg scrambler, and the electric tweezers.这是电沙拉干燥器、电罐头起子、电皂液器、电空气清新器、电卷发器、炒蛋器、电拔毛器的国土。
7.The drawing stress increased with the speed rise at low speed.在低速拉拔时,拉拔应力随拉拔速度的增加而增大。
8.A forcible extraction.拔出，拉出用力拔出或抽取
9.bright-drawn bar冷拉光条，光亮冷拔钢条
10.pluck or pull at with the fingers.用手指用力地拉或拔。
11.Transverse crack analysis of SWRH 82B wire rod drawingSWRH82B盘条拉拔横裂纹分析
12.To disconnect the AC power cord, pull it out by grasping the plug. Never pull the cord itself.拔取电源线时，请拿住插头拔出，切勿拉扯电源线。
13.altitude compensating carburetor高海拔补偿式化油器
14.(of a container) having the stopper removed.（关于容器）以拔掉塞子的。
15.PDFA (Praseodymium-Doped Fiber Amplifier)拔镨氟化物光纤放大器
16.The Numerical Simulation of Steel Tube Drawing Process with a Short Mandril and Optimizing Design for Tube Drawing Process and Mandril;钢管短芯棒拉拔过程的数值模拟及拉拔工艺、芯模的优化
17.Tension and shear test methods for building anchors建筑锚栓抗拉拔、抗剪性能试验方法
18.pulling-in dogs(拉拔用的)夹料钳，牵引链钳，带头线钳
相关短句/例句
piston puller活塞拉拔器
3)liner puller缸套拉拔器
4)puller[英]['pul?][美]['p?l?]拉出器;拔取器
5)cylinder-liner extractor气缸套拉拔器
6)cylinder-liner extractor汽缸套拉拔器
延伸阅读
拉拔分子式：CAS号：性质：用外力作用于被拉金属的前端，将金属坯料从小于坯料断面的模孔中拉出，使其断面减小而长度增加的方法。由于拉拔多在冷态下进行，因此也叫冷拔或冷拉。金属拉拔过程中，使用由皂基、硼砂、聚乙二醇油酸酯和水组成的乳液或由矿物油、脂肪酸、十二烷醇、油酸聚氧乙烯酯和水组成的乳液作为润滑剂，可减轻拔丝机械强度，提高拔丝速度和产品质量。
