压下量,reduction
1)reduction[英][r?'d?k?n][美][r?'d?k??n]压下量
1.Simulation on hot rolling compounding of two metal plates and determination of minimum relative reduction;双金属板热轧复合模拟及最小相对压下量的确定
2.Determination of minimum relative reduction in hot rollingcompounding of stainless and carbon steel plates;不锈钢-碳钢板热轧复合最小相对压下量的确定
3.Stress and strain analysis of H beam universal rolling in different flange reductions;H型钢轧制翼缘不同压下量的应力应变分析
英文短句/例句

1.Research and Application of Soft Reduction Amount in Bearing Steel GCr15 Bloom Continuous Casting轴承钢GCr15大方坯轻压下压下量参数的研究与应用
2.May I take your blood pressure ?给你量一下血压吗?
3.Let me take your blood pressure .让我量一下你血压。
4.constant flow nozzle恒定流量水枪压力下
5.Analysis on dynamic characteristics of pressure pump for hydraulic screw down system in cold rolling mill轧机液压压下系统恒压变量泵动态特征分析
6.When the downstream head is greater than about 3/5 of the upstream head, flow is submerged.当下游压头大于上游压头约3/5时,流量是潜流。
7.After the postal strike there be a huge backlog of undelivered mail邮政部门罢工以後, 大量邮件积压下来
8.the weight of a liter of hydrogen (at 0 Centigrade and 760 millimeters pressure).气压毫米下一公升氢的重量。
9.Increase code quality through beneficial peer pressure.* 可以在同等的压力下提升代码的质量。
10.After the postal strike there was a huge backlog of undelivered mail.邮政部门罢工以后, 大量邮件积压下来.
11.After the postal strike there are a huge backlog of undelivered mails邮政部门罢工以後,大量邮件积压下来
12.Objective Measurement Andlysis of Bra Stress Distribution under Static and Dynamic Status动静态下文胸压力分布客观测量分析
13.The measurement of scotopic pupil diameter with noncontact tonometer非接触眼压计测量暗适应下瞳孔直径
14.Synthesis of PcBN compacts with low cBN content under high pressure and high temperature低含量PcBN复合片在高温高压下的合成
15.Unloading deformation failure and energy properties of marble under high confining pressure and high water pressure高围压高水压条件下大理岩卸围压变形破坏与能量特征
16.Research of Compacted Materials Absorbing Effective Compaction Energy During Slip-rotation of Oscillatory Compaction振荡压实滑转工况下被碾压材料吸收有效压实能量的研究
17.To exert steady weight or force against;bear down on.挤压,按对…施加持续的重量或力量;在…上按下
18.Non-steady Flow Method for Measuring the Micro Flow at Constant Micropressure恒定微压下微小流量的非定常流测量方法
相关短句/例句

stroke of pressing down压下量
1.A method of determining high precise stroke of pressing down of straightening drill pipe is presented.对于这种专用的、尺寸大且要求校直精度高的管材 ,运用弹塑性理论建立了其压点式反弯校直数学模型 ,提出了一种精度较高的校直压下量的确定方法 。
2.A practical computation method for the stroke of pressing down is derived, which can be used to direct the straightening operation.给出了实用的确定矫直压下量参数的方法 ,从而为实际矫直工作提供了的理论指导 。
3)press amount下压量
1.The principle of cutting and splitting glass substrates of TFT-LCD and the impacts of craft parameters on cutting quality, such as scribe-wheel angle, cut pressure, press amount are studied in this paper.研究了TFT-LCD切割裂片的原理,以及刀轮角度、切割压力、下压量等工艺参数对切割质量的影响。
4)large percent reduction大压下量
1.The surface crease presenting in rolling with large percent reduction is simulated with finite element method,the law that process parameters affect rolling quality is found out.采用有限元法对大压下量轧制工艺下,轧件表面折皱的产生进行了模拟分析,找到了工艺参数对轧件质量的影响规律,经过对原工艺参数进行调整,达到了降低钢材表面折皱缺陷的目的。
5)total reduction amount总压下量
6)the quantity of lightly presses轻压下量
延伸阅读

压下量压下量draught  yaxiafiang压下t(draught)轧件轧制前的高度H与皿丫坠 ab 轧件尺寸图 a一轧制前;b一轧制后轧制后的高度h之差,一般以△h表示,因此有△h~H一h。它是表示轧制时轧件高度方向绝对压缩变形程度的变形参数。对横截面为矩形的轧件,其高度即矩形截面的实际高度(见图);对横截面不是矩形的轧件,其一一、._.一~、~~..._、._‘~=F。二F高度为平均高度,并按以下公式确定:H~丫,h~告,.,~,“,一,.,~’月‘~’“产、钊~’“B。”’B’式中万,再分别为轧制前、轧制后轧件的平均高度;F。,F分别为轧前轧后的横截面面积;B。,B分别为轧制前轧制后的宽度。 (余望)