1)burn-through-point烧穿点
1.An integrated prediction model for burn-through-point in lead-zinc sintering process铅锌烧结过程烧穿点的集成预测模型
英文短句/例句
1.An integrated prediction model for burn-through-point in lead-zinc sintering process铅锌烧结过程烧穿点的集成预测模型
2.A source said the burn-through probably occurred at a seal point between the booster's third and fourth sections.一位提供消息的人说，烧穿点可能发生在火箭的第三和第四部分之间的焊接点上。
3.To avoid burning through tube, the flame should be in continuous motion and not allowed to remain on any one point.为了避免烧穿管道，火焰应该持续移动，不要停留在任何固定点上。
4.Used for testing the flaming degree and speed of textile after being ignited.用于测量易燃纺织品穿着时，一旦点燃后燃烧的剧烈程度和速度。
5.flare point【化】燃烧点, 着火点
6.The burnt coil should be renewed.烧穿的线圈应换新的。
7.The ignition of fuel in an internal - combustion engine before the spark passes through the fuel, resulting from a hot spot in the cylinder or from too great a compression ratio for the fuel.提前点火由内燃机中的火星穿过燃料之前的燃烧，是因油缸热点过高或对燃料的过大压缩比造成的
8.Study On the Explosive Course of 12.7 mm-bored Armour-Piercing Explosive Incendiary Cartridge;12.7毫米穿甲爆炸燃烧弹爆炸过程研究
9.Setting fire to the letter, he made her watch it burn.他点火烧那些信时让她看着那信燃烧。
10.You're a bit feverish, you should go to bed.你有点发烧,你该上床去。
11.Capable of igniting and burning.可燃的能够点火及燃烧
12.You cannot burn the candle at both end.蜡烛两头点，瞬息即烧完。
13.piezoelectric burner igniter压电燃烧器点火装置
14.State Key Laboratory on Coal combustion煤燃烧国家重点实验室
15.Will this coal last out the winter?这点煤能够烧一冬吗？
16.it does not matter if the shoes feel a bit tight. They'll stretch with wearing.这种鞋小点不要紧, 穿穿就大了。
17.Better put on more clothes [your rubber shoes].最好多穿点衣裳并[穿上胶鞋]。
18.The act of inflaming or the state of being inflamed.点火，燃烧点火的动作或被点燃的状态
相关短句/例句
burn-through烧穿
1.Prediction of welding burn-through of pressured pipeline in-service;压力管道在线焊接烧穿的预测
2.But it is also very dangerous because burn-through might happen during welding.但是在役焊接时可能发生烧穿,有很大危险性。
3.The signification of repair high pressure gas pipelines and the types,complication of burn-through onto in-service welding were summarized.综述了高压气管线在役焊接修复的意义,以及烧穿的模式和影响因素,总结分析了国内外在役焊接烧穿的研究现状和进展。
3)burn through烧穿
1.All effecting factor of burn through wall thickness of pipeline during welding is mainly analyzed and highlighted the effect of welding parameter to pipeline fusion depth and obtained the best welding specification to reach the results of preventing burn through wall thickness.主要分析了管道焊接时烧穿管壁的各种影响因素,着重阐述了焊接参数对管线熔深的影响,得出了最佳焊接规范,达到了防止烧穿管壁的效果。
4)burning through烧穿
1.This paper describes causes of burning through in spot welding of thin plates with MMAW,and provides a welding current controlling circuit for preventing burning throug总结了手工电弧点焊１ｍｍ左右厚度薄板烧穿的原因，设计了一种防止薄板手工电弧点焊烧穿的焊接电流控制电路，获得了满意的效
5)furnace hearth damage炉缸烧穿
6)burnthrough range烧穿距离
1.The burnthrough range of multiple false targets jamming under standoff jamming is studied based on power rule.介绍了多假目标干扰的产生原理,分析了多假目标干扰的能量特征;基于功率准则对远距离支援干扰下多假目标干扰的烧穿距离进行了理论分析;最后通过地面警戒雷达的干扰试验验证了多假目标干扰的有效性。
2.This paper mainly researches the influence of the variety of target radar cross section(RCS) or active jamming power(the other conditions don t change)on radar burnthrough range and jamming effect under the self-defense jamming or support jamming mode,and draws the curves reflecting the relation between the burnthrough range and RCS & active jamming power.主要研究了在自卫或支援干扰方式下,目标雷达反射面积或有源干扰功率的变化(其它条件不变)对雷达烧穿距离和干扰效果的影响,并绘制了烧穿距离与雷达反射面积、有源干扰功率变化之间的曲线。
延伸阅读
穿踰1.见"穿窬"。
