断口形貌,fracture morphology英语短句,例句大全

断口形貌,fracture morphology
1)fracture morphology断口形貌
1.Analysis on structure and fracture morphology of short fiber reinforced aluminum-silicon alloy composites;短纤维增强铝硅合金复合材料的组织与断口形貌分析
2.Microstructure and fracture morphology of 37Mn5 continuous casting billet;37Mn5连铸坯显微组织及断口形貌研究
3.And the fracture morphology was analyzed by SEM.7%Cu合金熔体结构特征及变化过程,用扫描电镜观察断口形貌。

英文短句/例句

1.Mechanical Properties and Fracture of the Super-Tough PA6/ABS Alloy超韧PA6/ABS合金性能和断口形貌研究
2.The fractures of the alloys change from dimple to cleavage fracture with river pattern.合金的断口形貌由韧窝向河流花纹状的解理形貌转变。
3.The Study of the Process and the Rupture on the Explosion Welding-Rolling Ti-steel Composites Plate;爆炸焊接—轧制钛钢复合板——工艺和断口形貌研究
4.A Study on the On-line Prediction of Fracture Appearance Transition Temperature of 2.25Cr-1Mo Steel;2.25Cr-1Mo钢断口形貌转变温度在线预测方法研究
5.An Investigation on Fracture Morphology Differences between Gray Irons with A-Type and D-Type GraphiteA型和D型石墨合金灰铸铁断口形貌对比研究
6.The Effect of Permanent Mold on the Arm-Spacing and the Fatigue Fructographies of the Low Chromium V-Ti White Cast Iron;金属型铸造对低Cr─V─Ti白口铸铁枝晶间距和断口形貌的影响
7.The toughness, fractograph and microstructure of the failed die specimens have been examined and analysed.检测了失效模具材料的微观组织、击韧性和断口形貌。
8.ON THE RELATION BETWEEN INCLUSIONS AND MORPHOLOGY OF DIMPLE FRACTURES IN CERTAIN STEELS中碳镍铬钼钢中夹杂物和韧窝断口形貌关系的初步观察
9.Influence of B Refinement on Mechanical Properties and Fracture Surfaces of Hypoeutectic Al-Si AlloyB细化处理对亚共晶铝硅合金力学性能和断口形貌的影响
10.Quantitative Study of Macroscopical Metallic Fracture Surface Roughness金属断口宏观形貌表面粗糙度的定量研究
11.The fracture appearance is dimple at room temperature,it changes into intercrystalline fracture at low-temperature.其冲击断口微观形貌由室温时的韧窝断口逐渐变为低温下的塑性沿晶断口.
12.Fractographic analysis of failed fragment of In-Ceram alumina crown应用断口表面形貌分析法分析临床失败In-Ceram全瓷冠1例
13.Impact Fracture Curve and Fractured Surface Morphology of PA 6/POE BlendsPA 6/POE冲击断裂曲线及断面形貌
14.THE EFFECT OF MOLYBDENUM POWDER MORPHOLOGY ON FRACTURE PROPERTIES OF MOLYBDENUM WIRE钼粉形貌对钼丝断裂性能的影响研究
15.Fractography Analysis on Dynamic Fracture in Rock岩石动态断裂耗能机制的形貌学分析
16.The composite displays the fracture features of the dimple and intergranular fracture.复合材料的断裂形貌为韧窝加沿晶断裂。
17.The fractograph exhibited typical ductile dimple fracture pattern.断裂形式呈韧性断裂,断口以韧窝为主。
18.Characteristics Extraction of Metallic Corrosion Morphology for Corrosion Diagnosis;金属腐蚀形貌特征提取用于腐蚀诊断的研究

相关短句/例句

Fractography[fr?k't?ɡr?fi]断口形貌
1.Fractal Study of the Impact Fractography for D_6AC Steel;D_6AC钢冲击断口形貌的分形研究
2.The results indicate that the fractography change from tenacity to brittleness with the loading rate growing.本文研究了加载速率v对PBT拉伸断口形貌的影响,结果表明,随v的增大,试样断裂过程中裂纹扩展特征不同,断面形貌表现出由韧性断裂特征向脆性断裂特征的转变;断面平坦区比例参数AP/A0随v的增加先急剧增大,当v增大到1 000 mm/min以上时,AP/A0增加缓慢;断裂源处表面粗糙度参数RS和v呈线性关系,拟合得到的线性方程为:RS=2。
3.TC4 Ti alloy is welded using vacuum electron beam welding,microstructure and fractography is observed by means of optical metallography and scanning electron microscope,and microhardness test and impact experiment are conducted.采用真空电子束焊方法进行TC4钛合金的焊接,借助OM、SEM设备观察焊缝金属显微组织和断口形貌,测试了焊接接头硬度并进行了冲击试验,分析了焊接接头性能、显微组织及焊缝中气孔的形成。
3)fracture appearance断口形貌
1.Tensile properties and fracture appearance of 1Cr18Ni9Ti steel welded joint at low temperature;低温下1Cr18Ni9Ti钢焊接接头的拉伸性能和断口形貌研究
2.Tensile experiment was carried out and the fracture appearance was observed.在50钢表面进行等离子渗Cr,然后进行等离子超饱和渗碳、淬火及回火处理,获得表面强化层,并对处理后的材料进行拉伸试验和断口形貌观察。
3.Then tensile experiment was carried out and the fracture appearance was observed.对处理后的试样进行拉伸试验和断口形貌观察,结果表明:距表面的距离为0~0。
4)fracture surface断口形貌
1.The effect of different casting methods of sand mold and metal mold on the mechanical properties and fracture surfaces of ZL210A casting aluminum alloy of casting,solid-solution and aging was investigated.采用砂型和金属型两种不同铸造方法对铸态、固溶态和时效态ZL210A合金性能及断口形貌的影响进行研究。
2.The fracture surfaces of the composite were investigated at 490℃, 510℃, and 520℃ in a constant strain rate in order to analyse deformation mechanism.同时，利用扫描电镜观察断口形貌，分析了变形机
5)fractograph['fr?kt?uɡrɑ:f]断口形貌
1.The crack fractographs of X60 pipeline steel after 10% per-tension deformation under cyclic loading are investigated by the SEM.用扫描电镜(SEM)分析了X60管线钢在未变形和10%的预拉伸变形后循环载荷下的裂纹断口形貌。
2.Al matrix composites reinforced with various sizes and contents of SiCp were fabricated via powder metallurgy followed by hot extrusion,and their tensile properties and fractographs were examined.5%,5%)亚微米(130 nm)和微米级(14μm)的SiCp增强铝基复合材料,并对其拉伸性能及断口形貌进行了分析。
3.Study on the Fractograph of SiC/Al Composites by Pressureless Infiltration Technique;采用SEM、EDX等分析技术对无压浸渗法制备SiC/Al复合材料的断口形貌进行了分析。
6)fracture[英]['fr?kt??(r)][美]['fr?kt??]断口形貌
1.The fracture is toughness fracture.本文重点分析了σ_(max)为398MPa、477 MPa、588 Mpa和796 MPa时的断口形貌,初步探究其疲劳断裂机理。
2.The cross section fracture surface was observed and analyzed by SEM.利用扫描电镜和显微硬度及划痕试验对用反应磁控溅射法制备的TiN/C3N4复合涂层进行了较系统的研究,对TiN/C3N4复合涂层的横截面断口形貌进行了观察和分析。